Input power rules, from a snapshot of the source status.
More...
|
|
uint32_t | pd_min_established_vbus_mV (const uint32_t negotiatedVoltage_mV) |
| | Lowest VBUS measure for which the negociated voltage is considered established A fixed 1V margin blocked a 9V contract from another lamp: VBUS read 7.98V (issue #357)
|
| |
|
bool | is_vbus_from_own_output (const bool isSwitchingToOtg, const bool isChargerInOtg, const bool isOutputGateEnabled) |
| | True when the VBUS measure can come from our own OTG output, and is not a power source The charger OTG also powers the output gate (output mode), and the two gates are never enabled together: the USB port is then isolated from our output, and VBUS can only come from an external source. It must be followed, or a cable unplugged in output mode is never seen (issue #646). While the gates are switching (both disabled), the port can still hold our own voltage: it is ignored too.
|
| |
|
bool | is_unplugged (const uint32_t timeSinceVbusValid_ms, const bool isSinkHardResetting) |
| | VBUS was lost long enough to consider the source unplugged.
|
| |
|
bool | can_use_pd_full_power (const SourceStatus &s) |
| | The PD contract is established, and VBUS reached the negociated voltage.
|
| |
|
bool | is_standard_port (const SourceStatus &s) |
| | The source is a standard USB port (no PD), with a stabilize delay.
|
| |
|
bool | can_use_power (const SourceStatus &s) |
| | The source power can be used.
|
| |
|
uint16_t | max_input_current_mA (const SourceStatus &s) |
| | Maximum current that can be pulled from the source.
|
| |
|
|
static constexpr uint32_t | standardPortDetectionDelay_ms = 1500 |
| | Delay after a source detection (or a PD resume) before considering it a standard (non PD) port.
|
| |
|
static constexpr uint32_t | pdLostDelay_ms = 1000 |
| | Delay after the last PD source detection before considering it a standard port.
|
| |
| static constexpr uint32_t | maxPdNegociationWait_ms = 8000 |
| |
|
static constexpr uint16_t | standardPortCurrent_mA = 800 |
| | Current pulled from a standard port (ICO finds the real maximum)
|
| |
|
static constexpr uint32_t | pdSourceTolerance_percent = 5 |
| | PD source output tolerance (vSrcNew), in percents of the negociated voltage.
|
| |
|
static constexpr uint32_t | pdCableDrop_mV = 500 |
| | Cable and connectors voltage drop allowed on VBUS (USB-C, at 3A)
|
| |
|
static constexpr uint32_t | vbusMeasureResolution_mV = 420 |
| | VBUS measure resolution: the FUSB302 measure has 420mV steps, and rounds down.
|
| |
|
static constexpr float | pdCurrentRatio = 0.90f |
| | Do not use the whole PD current, or the source will cut us off.
|
| |
|
static constexpr uint32_t | unplugDeglitch_ms = 1000 |
| | VBUS can be lost this long before the source is considered unplugged (flicker, ICO algorithm)
|
| |
| static constexpr uint32_t | hardResetUnplugDeglitch_ms = 3000 |
| |
Input power rules, from a snapshot of the source status.
◆ hardResetUnplugDeglitch_ms
| constexpr uint32_t lampda::bsp::powerDelivery::policy::hardResetUnplugDeglitch_ms = 3000 |
|
staticconstexpr |
During a hard reset, the source drops VBUS: tSafe0V (650ms) + tSrcRecover (1000ms) + tSrcTurnOn (275ms) ~= 1.9s. VBUS can be lost this long before the source is considered unplugged. This limit does not depend on the PD state machine: if it stalls in a hard reset state, an unplug must still be detected (issue #642). Also used for a power role swap: old source turn off (tPSSourceOff, 920ms) + new source turn on (~400ms).
◆ maxPdNegociationWait_ms
| constexpr uint32_t lampda::bsp::powerDelivery::policy::maxPdNegociationWait_ms = 8000 |
|
staticconstexpr |
After this delay, the standard port fallback does not wait for the PD negociation anymore. It is only a guard against a stuck state machine: every negociation state has its own timeout. Worst case of a late negociation: CC debounce (200ms) + caps wait (600ms) + soft reset (30ms)
- 2 * (hard reset recovery (650ms + 1275ms) + caps wait (600ms)) ~= 5.9s