|
|
void | suspend_pd_state_machine () |
| | Suspend the execution of the power delivery state machine.
|
| |
|
void | allow_source_resets (const bool allow) |
| | Allow the sink to reset the source, when the source capabilities were missed. A hard reset makes the source drop VBUS for up to ~2s. Forbid it when the battery cannot power the board (recovery mode), or this browns it out: the source is then used as a standard 5V port. Forbidden until allowed. Allowing it later starts the reset of a source waiting for its capabilities.
|
| |
|
void | resume_pd_state_machine () |
| | resume the execution of the power delivery state machine
|
| |
|
int | get_vbus_voltage () |
| | use the vbus measure from negociator (close to USBC, 0 to N volts)
|
| |
|
bool | is_usb_pd () |
| |
|
policy::SourceStatus | get_source_status () |
| |
|
bool | can_use_PD_full_power () |
| |
|
bool | is_standard_port () |
| | return true if this voltage source is from a standard non pd port
|
| |
|
void | ic_interrupt () |
| |
| bool | is_ic_interrupt_pending () |
| |
|
bool | is_vbus_powered () |
| |
|
const char * | cc_level_str (const int level) |
| |
|
void | show_pd_contract () |
| |
|
void | show_pd_status () |
| | Debug power delivery status.
|
| |
| void | interrupt_handle () |
| |
|
void | pd_run () |
| |
|
bool | setup () |
| | call once at program start, attach interrupts and init
|
| |
|
void | start_threads () |
| | Start polling threads.
|
| |
|
void | loop () |
| | call often (update status)
|
| |
|
void | shutdown () |
| | call once at program end
|
| |
|
uint16_t | get_max_input_current () |
| | return the max current available for this source
|
| |
|
bool | is_power_available () |
| | Return true if some power is available on VBUS.
|
| |
|
bool | can_use_power () |
| | Return true if we can use this source as power entry.
|
| |
|
void | force_set_to_source_mode (const bool force) |
| | force the system to source mode
|
| |
|
OTGParameters | get_otg_parameters () |
| | Return the desired OTG parameters.
|
| |
|
void | allow_otg (const bool) |
| | Call to allow or forbid OTG mode.
|
| |
| void | want_source_role_by_swap (const bool wanted) |
| | As a sink, ask the partner for the source role (power role swap), and do not use its power meanwhile.
|
| |
|
bool | is_attached_as_sink () |
| | return true when the PD state machine is attached to a partner, as a sink
|
| |
|
void | retry_source_role_swap () |
| | As a ready sink wanting the source role (want_source_role_by_swap), ask for the power role swap again.
|
| |
|
bool | is_source_contract_ready () |
| | return true when we are a source, with a contract in place (PS_RDY sent): the sink can use the power
|
| |
|
bool | is_switching_to_otg () |
| | return true is the system is prepaping to switch to OTG mode
|
| |
|
bool | is_source_hard_resetting () |
| | return true when we are a source in a hard reset: VBUS must be cut until the end of the recovery time
|
| |
|
std::array< PDOTypes, 5 > | get_available_pd () |
| | If the charger is PD compatible, return it's capabilities.
|
| |
Handles the power delivery capabilities (USB-PD).
| bool lampda::bsp::powerDelivery::is_ic_interrupt_pending |
( |
| ) |
|
The FUSB302 interrupt line is level triggered (active low, until all interrupt registers are read), but we only get a callback on the falling edge. If an interrupt is raised before the callback is attached (VBUS and CC are already there at boot, the CC lines have a permanent Rd), or while another one is pending, there is no new falling edge: the line stays low forever, no message is received and no transmission completes (issue #633). So service the interrupt on the line level.